Desmontar un Nokia 7210, 6610

ShotGun · 10-feb-2008, 10:24

When dismantling any phone, great care should be taken to ensure that no damage is caused to any of the parts. Rough handling may result in severe damage of many parts, and if proper anti-static procedures are not followed, electrostatic damage may result in any electronic component.
Before commencing, it is recommended that the correct tools are purchased for the job in hand. At the very least, you will require a Torx T6 screwdriver. Do NOT attempt to use a small Allen key or filed down screwdriver, you will only damage the screws.
Please note that mechanically the 6610 is virtually identical to the 7210, so these instructions can be used for the 6610 as well.
Step 1. Remove the front and back covers, the battery and SIM card.

Step 2. On the front of the phone you will see six Torx T6 screws (highlighted in red). Remove these and keep them in a safe place.

Step 3. With the six screws removed, you can simply list the display/keypad unit and the main circuit board away from the phone. Note that the main board and display/ keypad unit are held together by the rubber grommet that can be seen in the photo below towards the top-right of the main board.

Step 4. The only bits left to remove are shown below along with their corresponding positions on the back plate. Infra red sensor cover, power button and volume buttons, charging port and the vibra motor.

Step 5. To re-assemble the phone, simply reverse the above steps. After re-assembly take as much time as you need to thoroughly test the handset to ensure that you have caused no damage, or forgotten one of the re-assembly steps.

10-feb-2008, 10:24	#1
ShotGun Senior Member Fecha de Ingreso: octubre-2004 Edad: 22 Mensajes: 440 Agradecio: 0 Agradecio 8 veces en 8 Mensajes	Desmontar un Nokia 7210, 6610 When dismantling any phone, great care should be taken to ensure that no damage is caused to any of the parts. Rough handling may result in severe damage of many parts, and if proper anti-static procedures are not followed, electrostatic damage may result in any electronic component. Before commencing, it is recommended that the correct tools are purchased for the job in hand. At the very least, you will require a Torx T6 screwdriver. Do NOT attempt to use a small Allen key or filed down screwdriver, you will only damage the screws. Please note that mechanically the 6610 is virtually identical to the 7210, so these instructions can be used for the 6610 as well. Step 1. Remove the front and back covers, the battery and SIM card. Step 2. On the front of the phone you will see six Torx T6 screws (highlighted in red). Remove these and keep them in a safe place. Step 3. With the six screws removed, you can simply list the display/keypad unit and the main circuit board away from the phone. Note that the main board and display/ keypad unit are held together by the rubber grommet that can be seen in the photo below towards the top-right of the main board. Step 4. The only bits left to remove are shown below along with their corresponding positions on the back plate. Infra red sensor cover, power button and volume buttons, charging port and the vibra motor. Step 5. To re-assemble the phone, simply reverse the above steps. After re-assembly take as much time as you need to thoroughly test the handset to ensure that you have caused no damage, or forgotten one of the re-assembly steps.

Herramientas
Mostrar Versión Imprimible Enviar por Correo
Desplegado
Mode Lineal Cambiar a Modo Hibrido Cambiar a Modo Hilado

Temas Similares
Tema	Autor	Foro	Respuestas	Último mensaje
El Gran Libro De La Repostería	pelitonet	Gastronomía	1	24-sep-2008 17:11
descarga y convierte tus videos a 3gp para celular	pelitonet	Moviles & Celulares	4	14-ago-2008 15:35
Atomix Virtual DJ Professional v5.0.7 en Español	GeOrGe-89	Software	0	19-abr-2008 13:14
Resetea cualquier codigo de seguridad	pelitonet	Samsung	0	18-abr-2008 15:05
Ingenieria de Control Moderna	pelitonet	Humanidades	0	18-abr-2008 14:38